Marquis Spas Reward Owner's Manual download pdf (Page 16)

M A R Q U I S S P A S

OWNER’S MANUAL

SPIRIT™

# Component Identification Quantity

1 HK™8 Neck Jets 2

2 HK™12 Jets 12

3 HK™16 Jets 1

4 HK™40 Jets 4

5 Light* 1

7 Suction Fitting 1

8 Floor Drain 1

9 Jet Selector 1

10 Neck Jet Valve 1

11 Bather’s Control Panel 1

12 Filter Canisters 2

13 Spa Frog®* 1

14 Spa Frog® Return Fitting* 1

15 Ozone Injector Fitting* 1

16 Waterfall Feature* 1

17 Waterfall Valve* 1

19 Constellation* 12

20 Cushioned Headrests* 2

21 Adagio™ Speakers* 2

22 Water Feature* 1

TROUBLESHOOTING GUIDE

PLEASE NOTE: The following corrective actions may be performed by the spa

owner. If the trouble cannot be corrected in the steps below, please contact your

authorized Marquis spa dealer for service. (Improper servicing by an unauthorized

service provider or spa owner could result in damage not covered by the warranty and

could cause serious injury.)

EQUIPMENT WILL NOT OPERATE

• Check the control panel LCD window for diagnostic code.

• Check the circuit breaker on the main circuit panel.

• Check the condition of the power cord.

INADEQUATE JET ACTION

• Be sure the shut-off valves are completely open.

• Open the jets by turning the jet face to allow for maximum water flow.

• Check that the air control valve is open (rotate lever counterclockwise).

• Check for obstruction or restrictions at suction guard(s) or filters, such as

leaves.

• Check that the water is at proper level, 2/3 up the Vortex skimmer

opening(s).

• Inspect the filter cartridge(s) for dirt and debris.

• Check for pump air lock.

Physical Specifications Size

JET VALVES ARE HARD TO OPERATE

Dimensions/mm 2134 x 1524

• Valves and rotating jets that become hard to turn is an indication of sand, dirt

or too high calcium level in the water.

Height/mm 749

Corner Radius/mm 432

Seating Capacity/Positions 3/4

• Remove components and rinse before damage occurs.

Weight Dry/Kgs. 186

• Advise bathers to shower or use a foot bath before entering the spa. Failure to

use or maintain valves as directed may cause damage by introduction of foreign

materials such as dirt, sand and calcium that is not covered under the warranty.

Weight Full/Kgs. 810

Water Capacity/Litres 623

Total Therapy Jets 19

NO HEAT

• Check temperature displayed in the LCD window for desired temperature setting.

• Inspect the filter cartridge(s) for dirt and debris.

• Check that the water is at proper level, 2/3 up the Vortex skimmer

opening(s).

• Check HEAT MODE to be certain spa is not in SLEEP MODE or ECONOMY

MODE.

• Lower ambient temperatures may result in heat loss.

NOTE: Do not expect instant hot water from the jets. It will take the heater 12-24

hours to heat the water to the temperature you desire.

Spirit Zone Control

ZONE 1A

Upper-, mid- and lower-back jets.**

ZONE 1B

Lower- body jets.**

*Items are optional. Check with dealer for

availability.

**HK™8 Neck Jets operate in every zone.

LIGHT DOES NOT WORK

• Press the LIGHT pad on the control panel.

• Reposition the light bulb in the socket. (See REPLACING LIGHT BULB.)

• Replace the light bulb with similar component only.

OZONATOR BUILDUP

There can be a build up of nitrous compounds that typically gather at the ozone

outlet connection to the tubing after a six to 12 month period. If you see a

“gummy” build up at the point where the ozone tubing is connected to the ozone

generator, do the following:

• Turn electrical power off.

• Disconnect the tubing and clean it out using a Q-tip dipped in white vinegar.

Take care to avoid cracking or breakage when you remove the tubing from

the barbed fitting.

LCD DIAGNOSTIC MESSAGES

The advanced technology built into the spa allows it to perform a number of self-

diagnostic system checks and it can display a variety of messages in the LCD

window on the control panel.

OHH, HH: Over heat protection. If a malfunction occurs and the spa water

reaches 44°C, the system completely shuts down. In such a condition, DO NOT

ENTER THE WATER. Turn off all power to the spa. Remove spa cover and

allow water to cool. Once the heater has cooled, turn on power to the spa, then

reset by pushing any pad. If spa does not reset, shut off the power to the spa

and contact your authorized Marquis Spas® dealer for service. Several

conditions could lead to overheating, for example, low water level, shut-off

valves closed while heater is on, dirty filter, and restriction in the plumbing lines.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23

Comments to this Manuals

No comments

Marquis Spas Reward Owner's Manual Page 16

Comments to this Manuals

Related products and manuals for Above ground pool accessories Marquis Spas Reward